Added a Kconfig option to enable SOC_DCDC_NRF52X_HV for nice_nano_v2
and mikoto. According to Nordic's documentation, the DC/DC regulator is
more efficient than the LDO regulator, so this is enabled by default.
The following boards do not support this mode and were not changed:
- nice_nano
- nice60
- nrfmicro_11, nrfmicro_13
- nrf52840_m2
- bluemicro840
I could not find schematics to confirm whether the following boards
support this mode:
- bt60_v1, bt60_v2
- bt65_v1
- bt75_v1
- corneish_zen_v1, corneish_zen_v2
- pillbug
- puchi_ble_v1
- s40nc
The devicetree pulls always add on to the extra pulls configured by toggle mode, so these should not have pulls defined in the devicetree. Saved ~200uA avg on another board with a 3t toggle switch
* In order to be sure the rest of the system is fully ready before
intializing, because init may result in immediate events being
triggered when used with toggle direct kscan inner devices.
* Add dedicated init priority for the sideband kscan.
* Refactor sideband code for clarity.
* Tweaks to direct kscan for clarity.
* Make sideband behavior row optional for brevity.
* Allow overriding ZMK Uno sideband behaviors.
* Instead of gpio key behavior trigger, add new kscan driver that
decorates/wraps a given kscan driver and will invoke basic system
behavior assigned to a given row + column, without the need for keymap
mapping in the matrix transform, bypassing keymaps entirely.
* Better naming for gpio-key behavior triggers.
* Tweaks to scanned behavior trigger to avoid bad semaphore use,
and reduce chance of issues with slowly scanned matrixes.
* Various code cleanups of style issues.
* Move to explicit enable of `ZMK_PM_SOFT_OFF` to turn
on the feature and use the behaviors, which matches
how other features work, and helps with split and
testing schemes.
Initial work on a soft on/off support for ZMK. Triggering soft off
puts the device into deep sleep with only a specific GPIO pin
configured to wake the device, avoiding waking from other key
presses in the matrix like the normal deep sleep.
Co-authored-by: Cem Aksoylar <caksoylar@users.noreply.github.com>
* To be able to use the Zephyr `voltage-divider` driver,
add a mode for fetching raw voltage from the sensor
and do state of charge calculation outside of the driver.
* Add a dedicated settings reset on start init priority and default
it to lower priority (high number) than default FLASH_INIT_PRIORITY
to be sure flash is initialized before we open the area.
Added a new CONFIG_ZMK_SETTINGS_RESET_ON_START option which enables init
code to call zmk_settings_erase(), and changed the settings_reset shield
to use it instead of CONFIG_ZMK_BLE_CLEAR_BONDS_ON_START, so it now
resets all settings instead of just clearing BLE bonds.
CONFIG_ZMK_BLE_CLEAR_BONDS_ON_START is left in place for now in case
someone still needs it. It may be replaced in the future once we find a
better way to repair a broken split connection.
Added a zmk_settings_erase() function to clear all saved settings. This
does not go through Zephyr's settings subsystem, but instead directly
clears the data from the setting storage backend, so a reboot is needed
for it to take effect.
* Handle board keymap location for boards with Zephyr
board revisions included.
* Includes bare non-revision file and a revision specific keymap
in case newer revision changes the layout/key positions.
* Don't default heap mempool by default now that there's a dedicated
LVGL mempool
* Set proper defaults for CiZ display hardware/custom screen.
* Double the dedicated display thread stack size for CiZ.
* Move to local/stack allocated event API that doesn't require
dynamic allocation/freeing.
* Disable heap, we no longer use alloc/free unless using LVGL.
* Tons of refactors all over to account for the new event approach.
zmk_battery_start_reporting() may be called from battery_event_listener(), which
will result in a bus fault when attempting to read a battery that does not exist
such as on a dongle.
* If attempting to notify and getting an EPERM return value, request
upgrading the security of the connection at that moment, since it
likely means we got a connection to a bonded host but the connection
hasn't been upgraded to encrypted yet.
* Add security related tests to verify behavior when trying to read
a GATT characteristic from our peripheral with and without client
auto security request/retry.
* Auto security request actually makes macOS worse, so disable it,
and remove our early request in favor of using GATT enforcement
to ensure connections are secured.
Note there was one place where a non-strict prototype was actually being used
with an argument, in `zmk_hog_init`. In this case, the actual argument type was
added instead.
* Add ability to fetch and report peripheral battery levels
on split centrals.
* Add additional support for adding a new Battery Level
service to split centrals that exposes fetched peripheral
battery levels to connected hosts.
Co-authored-by: Peter Johanson <peter@peterjohanson.com>
* Among other issues, this message is often misinterpreted by users
building out-of-tree shields -- leading them to think the shield
"not being found" is the cause of a build failure.
* Add a new Kconfig symbol to enable the low priority queue, and make
the two features that depend on it `select` the symbol to turn it on.
This helps ensure no wasted RAM/ROM on devices that don't need it.
* Split connection and security experimental changes into dedicated
Kconfig flags for easier testing of only connection related fixes.
Co-authored-by: Cem Aksoylar <caksoylar@users.noreply.github.com>
* Shift to using an extra Zephyr module to do keymap location
work after all board roots are resolved. This avoids duplicate work
and allows us to load custom boards from Zephyr modules as well as
user config setups.
Removed the label property from built-in behaviors, custom behaviors
defined in a few keymaps, and macros generated with ZMK_MACRO().
Now that node names are used to identify behaviors, and names only need
to be unique within the set of behaviors, the names of all behaviors
have been shortened to be similar to their original labels.
This means that any keymaps which reference behavior nodes by name
instead of by label will need to be updated. Keymaps typically use the
labels though, so most keymaps should be unaffected by this change.
Added BEHAVIOR_DT_DEFINE() and BEHAVIOR_DT_INST_DEFINE(), which work
exactly like the DEVICE_*_DEFINE() macros, except they also register the
device as a behavior by adding a pointer to it to a memory section.
Added zmk_behavior_get_binding(), which works like device_get_binding()
except that it only searches the devices that have been registered as
behaviors. This ensures that behaviors cannot have name collisions with
other devices defined by the SoC, which will be important when we remove
the label property from behaviors so they are given their node names.
As an added benefit, this is faster since it searches a smaller list.
Some basic benchmark code I wrote indicates it takes 30-70% as long,
depending on where the behavior is in the list and whether the name
string is an exact pointer match.
From now on, behaviors should use BEHAVIOR_*_DEFINe() instead of
DEVICE_*_DEFINE(), and any code that looks up a behavior by name should
use zmk_behavior_get_binding() instead of device_get_binding().
Changed the property used to define a layer name for displays from
"label" (which affects other things in Zephyr and is deprecated) to
"display-name". (It cannot be named simply "name", because that has
special meaning in newer versions of the devicetree compiler.)
"label" is still supported as a fallback, so no changes need to be made
to existing keymaps.
Removed "label" properties which no longer have any function.
Labels are still used as layer names and as identifiers for sending
behaviors between sides of a split keyboard, so those have been left
alone for now.
Changed the label property on zmk,ext-power-generic to be optional and
removed it from existing uses. Renamed the nodes for all non-development
boards to "EXT_POWER" to preserve user settings.
rgb_underglow.c now finds the correct device by finding the first
instance of zmk,ext-power-generic instead of looking for a node named
"EXT_POWER".
Changed all code (except for layer names) which used the label property
to use DEVICE_DT_NAME() instead, which uses the label if set or falls
back to the full node name. This matches how Zephyr determines the node
names used with device_get_binding() and allows us to start removing the
deprecated label property from things.
There is already a function to see if the peripheral is connected, a matching one for if it's bonded is a useful addition for displays/indicators. `is_bonded` gets reset to false in the advertising function in preparation for runtime peripheral bond clearing
German Gutierrez
Joel Spadin
Horu
ReFil
Peter Johanson
Jarryd Tilbrook
Pablo Martínez
Sadek Baroudi
Keeley Hoek
Xudong Zheng
Tobias Arndt
Thomas Huber
Theo Lemay
Theo Lemay
Pablo
honorless
Hans Kruse
Seth Milliken
ton-im
zhiayang
ctranstrum
Cem Aksoylar
senseored
Leonardo Bispo
Chris Andreae
moergo-sc
Justin Ridgewell
Gabor Hornyak
Hooky